TASCAM 208I USB AUDIO/MIDI INTERFACE M/ DSP MIXER

TASCAM 208I USB AUDIO/MIDI INTERFACE M/ DSP MIXER - Nummeret større end Tascams 102i. Dette lækre, kompakte lydkort: SERIES 208i audio / MIDI interface er perfekt til guitarister, bassister, sangskrivere m.m. og super velegnet til brug i små studier. Den giver op til ti lydindgange og to lydudgange til en Mac eller Windows-computer eller en iOS-enhed til optagelse og afspilning på op til 192 kHz / 24 bit og med den fantastiske lyd, man forventer af Tascam. Selvfølgelig som i 102i kommer 208i med DSP input og output mixer med indbygget digital reverb, kompressor, fase inverter og 4-bånds EQ for hver kanal.

Specs:

Provides up to 20 audio inputs and eight audio outputs to a Windows or Mac computer or iOS device 
Audio resolution up to 192 kHz / 24 bit 
USB Audio Compliance 2.0 for iOS connection 

Hardware features 
Four analogue mic/line inputs on XLR/TRS balanced combo connectors 
High-grade Ultra-HDDA (High Definition Discrete Architecture) microphone pre-amps with ultra-low noise (EIN: –129 dBu) 
High-quality audio input circuits for low-noise recording 
Individually switchable 48-Volt phantom power on XLR inputs 
Each TRS input can be switched to instrument-level for direct recording of guitar or bass 
Gain controls, signal and peak indicators on each analogue input 
Two optical audio inputs supporting S/MUX for high sampling rates 16 inputs at 44.1/48 kHz 
8 inputs at 88.2/96 kHz 
4 inputs at 176.4/192 kHz 

Eight line outputs (balanced TRS) 
Line outputs 1–2 can be used as monitor output with level control 
Direct monitor option for low-latency monitoring 
Monitor mix control for adjusting the level balance between signals from external devices and signals from the computer 
Two 6.3-mm standard headphones outputs with level control (45 mW per channel) 
Wordclock input and output for integration with other digital equipment 
MIDI input, MIDI output 
USB 2.0 computer connection 
Power supply by dedicated PS-P1220E AC adapter (included) 
Rugged all-metal chassis 

Software features 
In-house developed driver for Windows devices ensures stable operation with low latency 
Built-in DSP with mixer, routing and effects accessible through dedicated settings panel Compressor and 4-band EQ with low-cut filter on each input channel 
Phase invert, Bypass, Solo, channel Link and Mute buttons on each input channel 
Four Aux sends, switchable pre/post (Aux 1 used for internal reverb) 
Reverb effect with five presets and adjustable pre delay, reverb time, diffusion and return level (Reverb can be used up to 96 kHz only) 
Master section with Stereo fader, Aux Master controls and Mute button 
Comfortable routing of output channels 

Bundled with Cubase LE 9.5 (64-bit Windows application), compatible with Cubasis LE2 
Bundled with several plug-in effects 
Automatic update function available for software, driver and firmware updates 
Compatible with major DAW software (Pro Tools, Live, Cubase, Studio One, GarageBand etc.) 
Specifications


General ratings

Sampling frequencies   44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz  
Quantization bit depth   16/24-bit  


Analogue audio inputs 

Mic inputs (when the input switch set to MIC/LINE)   XLR-3-31 (1: GND, 2: HOT, 3: COLD)  
  Input impedance   1.5 kΩ  
  Nominal input level   −63 dBu (0.00055 Vrms, gain knob max.)
−6 dBu (0.195 Vrms, gain knob min.)  
  Maximum input level   +10 dBu (2.45 Vrms)  
  Maximum gain   57 dB  
Instrument inputs (when the input switch is set to INST)   6.3-mm standard TS jack 
(Tip: HOT, Sleeve: GND)  
  Input impedance   ≥1 MΩ  
  Nominal input level   −63 dBV (0.0007 Vrms, gain knob max.)
−6 dBV (0.501 Vrms, gain knob min.)  
  Maximum input level   +10 dBV (3.162 Vrms)  
  Maximum gain   57 dB  
Line inputs (when the input switch set to MIC/LINE)   6.3-mm TRS jack 
(Tip: HOT, Ring: COLD, Sleeve: GND)  
  Input impedance   10 kΩ  
  Nominal input level   −53 dBu (0.0022 Vrms, gain knob max.)
+4 dBu (1.228 Vrms, gain knob at min.)  
  Maximum input level   +24 dBu (12.282 Vrms)  
  Maximum gain   57 dB  


Analogue audio outputs 

Line outputs (balanced)   6.3-mm TRS jack 
(Tip: HOT, Ring: COLD, Sleeve: GND)  
  Output impedance   230 Ω  
  Nominal output level   +4 dBu (1.228 Vrms)  
  Maximum output level   +20 dBu (7.75 Vrms)  
Headphone outputs (PHONES)   Standard 6.3-mm stereo jack  
  Maximum output power (THD+N ≤0,1 %, 32 Ω)   45 mW + 45 mW 


Digital audio inputs/outputs 

OPTICAL IN (S/MUX) connector(s)   Optical (JEITA RC-5720C)  
  Signal format   Multi-channel optical format
(Supports S/MUX when 88.2 kHz, 96 kHz, 176.4 kHz or 192 kHz.)  


Other inputs and outputs 

USB   4-pin USB B-type  
  Transfer rate   USB 2.0 Hi-speed (480 MBit/s)  
MIDI input   5-pin DIN  
  Format   Standard MIDI format  
MIDI output   5-pin DIN  
  Format   Standard MIDI format  
WORD input   BNC  
  Input voltage   2.0 Vpp – 5.0 Vpp  
  Input impedance   75 Ω ±10%  
Permitted frequency deviation during external synchronization   ±100 ppm  
WORD output   BNC  
  Input voltage   2 Vpp (into 75 Ω load)  
  Output impedance   75 Ω ±10%  
  Sampling frequencies   44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz  


Audio performance 

Mic amp EIN (equivalent input noise)   ≤−127 dBu  
Frequency response (input to line output)      
  At 44.1/48 kHz   20 Hz – 20 kHz, +0/–1 dB (JEITA)  
  At 88.2/96 kHz   20 Hz – 40 kHz, +0/–2 dB (JEITA)  
  At 176.4/192 kHz   20 Hz – 80 kHz, +0/–10 dB (JEITA)  
S/N ratio   ≥106 dB
(MIC/LINE input to LINE output 1-2, gain knob at minimum, JEITA)  
Distortion   ≤0.005 %
(MIC/LINE input to LINE output 1-2, 1 kHz sine wave, −2 dBFS input level, MONITOR knob at maximum)  
Crosstalk   ≥95 dB
(MIC/LINE input to LINE output 1-2, 1 kHz sine wave, gain knob at minimum)  


Computer system requirements 

Windows      
  Supported operating systems   Windows 10 32-bit
Windows 10 64-bit
Windows 8.1 32-bit
Windows 8.1 64-bit
Windows 7 32-bit SP1 or later
Windows 7 64-bit SP1 or later
(Windows Vista and Windows XP are not supported)  
  Computer hardware requirements   Windows computer with a USB port that supports at least USB 2.0 or USB 3.0  
  CPU/processor speed   2 GHz or faster dual core processor (x86)  
  Memory   2 GB or more  
Mac      
  Supported operating systems   macOS Mojave (10.14 or later)
macOS High Sierra (10.13 or later)
macOS Sierra (10.12 or later)  
  Computer hardware requirements   Mac with a USB port that supports at least USB 2.0 or USB 3.0  
  CPU/processor speed   2 GHz or faster dual core processor  
  Memory   2 GB or more  
iOS device   Apple iOS device running iOS 10 or later  
Supported audio drivers   Windows: USB Audio Class 2.0, ASIO 2.2, WDM (MME), MIDI
Mac: Core Audio, Core MIDI
iOS device: Core Audio for iPhone  


Power supply and other specifications 

Power   DC 12 V AC adapter (PS-P1220E)  
Power consumption   14 W  
Dimensions (W × H × D)   296 mm × 65 mm × 160 mm  
Weight   1.5 kg  
Permissible operating temperature range   5–35 °C  

Mere information